CIMR-V7AM22P2 Yaskawa

 

 

MVA011 Magnetek

 

3G3MV-C2022 Omron

PC722P2 Saftronics

CIMR-V7AK22P2 Yaskawa

 

CIMR-V7AU22P2 Yaskawa

 

CIMR-V7CU22P24 Yaskawa

 

3 HP, Série V7

Le V7 était un lecteur compact à faible coût et haute performance, utilisable en mode V / f ou Open Loop Vector. En plus d'une bonne régulation de la vitesse, la commande vectorielle en boucle ouverte fournissait également un couple plus élevé à des vitesses plus basses. Le V7 était idéal pour les applications telles que les convoyeurs, les broyeurs, les centrifugeuses, les pompes, les ventilateurs, les soufflantes, les machines-outils, l'emballage, le traitement des aliments et la buanderie commerciale.

 

 

---

Codes d'erreur

 

 

 

 

Uu (Blinking)

Explanation : UV (Mail circuit low voltage)

                     Main Circuit DC voltage drops below the low-voltage detection level while the drive output is OFF.

                      230V : Stops at main circuit DC voltage below approx. 200V (160V for sinple-phase)

                       460V : Stops at main circuit DC voltage below approx. 400V

Possible solutions : Check the following :

                             Power supply voltage

                              Main circuit power supply wiring is connected.

                               Terminal screws are securely tightened.

 

ou (Blinking)

 

Explanation : OV (Main circuit overvoltage)

                     Main circuit DC voltage exceeds the over voltage detection level while the drive output is OFF. Detection level : approx. 410V or more (approx. 820V for 460V class).

Possible solutions : Check the power supply voltage.

 

oL3 (Blinking)

 

Explanation : OL 3 (Overtorque detection)

                     Motor current exceeded the preset value in parameter N098.

Possible solutions : Reduce the load, and increase the accel/decel time.

 

bb (Blinking)

 

Explanation : BB (External baseblock)

                     Baseblock command at multi-function terminal is active, the drive output is shit OFF (motor coasting). Temporary condition is cleared when input command is removed.

Possible solutions : Check the external circuit (sequence)

 

EF (Blinking)

 

Explanation : EF (Simultaneous FWD/REV run commands)

                    When FWD and REV run commands are simultaneously input the over 500 ms, the drive stops accorcing to parameter n005.

Possible solutions : Check the external circuit (sequence).

 

 

FAN (Blinking)

 

Explanation : FAN (Cooling fan fault) Cooling fan is locked.

Possible solutions : Check the following :

                              Cooling fan

                               Cooling fak wiring is not disconnected.

 

oC

 

Explanation : OC (Overcurrent)

                     Drive output current momenarily exceeds approx. 250% of rated current.

Causes : Short circuit at drive output side

                Excessive load inertia

                Extremely rapid accel/decel time (Parameters n019 to022)

                Special motor used

                Starting motor during coasting

                Motor of a capacity greater than the drive rating has been started.

                Magnetic contactor open/closed at the drive output side.

 

ou

                                  

Explanation : OV (Main circuit over voltage)

                     Main citcuit DC voltage exceeds the overvoltage detection level because of excessive regenerative energy from the motor.

                       230V : Stops at main circuit DC voltage below approx. 410V.

                       260V : Stops at main circuit DC voltage approx. 820V. or more.

Possible solutions : Increase decel time.

                             Connect optional dynamic braking resistor.

 

Uu1

 

Explanation : UV1 (Main circuit low voltage)

                     Main circuit DC voltage drops below the low-voltage detection lebel while the drive output is ON.

Possible solutions : Check the following :

                              Power supply voltage

                              Main circuit power supply wiring is connected.

                               Terminal screws are securely tightened.

 

 

 Uu2

 

Explanation : UV2 (Control power supply fault)

                     Voltage fault of control power supply is detected.

Possible solutions : Cycle power to the drive.If the fault remains, contact DMEB Service at 418-228-5984 or support@dmebservice.com

 

 

oL1

 

Explanation : OL1 (Motor overload)

                     Motor overload protection operates by built-in electronic thermal overload relay.

Possible solutions : Check the load size or V/f pattern setting (parameters n011 to n017)

                              Set the motor rated current shown on the nameplace in parameter n036

 

oL2

 

Explanation : OL2 (Drive overload)

                    Drive overload protection operates by built-in electronic thermal overload relay.

Possible solutions : Check the load size or V/f pattern setting (parameters no011 ti n017)

                              Check the drive capacity.

 

oL3

 

Explanation : OL3 (Overtorque detection)

                     V/f mode : Drive output current exceeded the preset value in parameter n098.

                      Open Loop Vector mode : Motor current or torque exceeded the preset value in parameters n097 and n098.

                        When overtorque is detected, drive performs operation according to the preset setting of parameter n096.

Possible solutions : Check the driven machine and correct the cause of the fault. Increase the value of parameter n098 up to the highest value allowed for the machine.

 

 

 EF

 

Explanation : EF (External fault)

                     Drive receives an external fault input from control circuit terminal.

                      EF0 : External fault reference through MODBUS communications.

                      EF1 : External fault input command from control circuit terminal S1.

                      EF2 : External fault input command from control circuit terminal S2.

                      EF3 : External fault input command from control circuit terminal S3.

                       EF4 : External fault input command from control circuit terminal S4.

                       EF5 : External fault input command from control circuit terminal S5.

                        EF6 : External fault input command from control circuit terminal S6.

                        EF7 : External fault input command from control circuit terminal S7.

Possible solutions : Check the external circuit (sequence)

 

F00

 

Explanation : CPF-00

                    Drive cannot communicate with the digital operator for 5 sec or more when power is turner ON.

Possible solutions : Cycle power after checking the digital operator is securely mounted. If the default remains, replace the digital operator or call us 418-228-5984.

 

F01

 

Explanation : CPF-01

                    Transmission fault occured for 5 sec or more when transmission starts with the digital operator.

Possible solutions : Cycle power after checking the digital operator is securely mounted. If the default remains, replace the digital operator or call us 418-228-5984.

 

F04

 

Explanation : CPF-04

                     EEPROM fault or drive control circuit is detected.

Possible solutions : Record all parameter data and initialize the constants

                             Cycle power to the drive.

                              If fault remains. Contact us support@dmebservice.com

 

F05

 

Explanation : CPF-05

                    A/D converter fault is detected.

Possible solutions : Cycle power.

                               If the fault remains, contact DMEB Service.

F06

Explanation : CPF-06

                     Option card connecting fault.

Possible solutions : Remove power to the drive.

                              Check the connection of the digital operator.

 

F07

Explanation : CPF-07

                     Operator control circuit (EEPROM or A/D converter) fault

Possible solutions : Cycle power after checking the digital operator is securely mounted. If the default remains, replace the digital operator or call us 418-228-5984.